Disclosure: As An Amazon Associate, I Earn From Qualifying Purchases

If you are struggling with the traditional roofing method and the amount of labor and cost it requires, then rolled roofing can be a perfect solution for you.  It is cheap as well as easy to install. 

But as you are here you might have a question on your mind that Can you use rolled roofing on a pitched roof? 

Well, rolled roofing is usually used in the low sloped roofs or where the look of the roof is not that important. However, you still can consider using it on a pitched or sloped roof. 

Let’s learn more from this article.

Can You Use Rolled Roofing On A Pitched Roof: An Ultimate Guide

Roll roofing can be considered for a practical alternative when aesthetic look isn’t as vital. It’s built of materials comparable to composition shingles. But isn’t as durable.

Check the warranties, and it may be limited to one year. It will last longer if you install roll roofing using the double-coverage approach.

How to Do Rolled Roofing on a Pitched Roof

Installing rolled roofing is different based on the slope of the roof. It is pretty easy for a low-sloped roof. But for a pitched roof, you may use the exposed nail roofing method.

Tools and materials

  • Measuring tape
  • Power nailer
  • Utility knife 
  • Carpenter’s square
  • Chalk line 
  • Roll Roofing
  • Roofing cement
  • Flashing
  • Nails
Rolled Roofing On A Pitched Roof
Check On Amazon
Roofing cement Rolled Roofing On A Pitched Roof
Check On Amazon
Power nailer for Rolled Roofing On A Pitched Roof
Check On Amazon

Installation Process

Rolled Roofing On A Pitched Roof
Credit: https://civiltoday.com/construction/building/301-what-is-pitched-roof-parts-and-types-of-pitched-roof

Step #1

Place a full-width sheet such that the lower edge and ends of the sheet are 1/4″ to 3/8″ overhanging the rakes and eaves. Nail in a 1/2″ to 3/4″ broad line top edge of the sheet should be parallel with. And the nails should be spacing 18″ to 20″ inches apart. 

The nailing of the top holds the sheet until the second layer is laid over  and connected. Nail the rakes and eaves on line 1″ parallel to the roofing margins, with nails spaced 3″ on center a bit along the eaves, to save the deck from breaking.

Step #2

Place the second layer longer than the first one. locate the second layer along the top edge using the same nailing instructions as the first.

Lift the lower border of the overlapping sheet and evenly apply lap cement to the upper two courses of the first course before the overlapping layer is embedded. 

Secure the lap with 3” nails in position by placing it in the center and slightly staggered. Place the nails at least 3/4 of the way down away from the edge of the sheet. In the same way as the first layer, the rake edges should be nailed. 

Step #3

When the roofing meets at a hip or ridge try to trim and nail it. Draw a parallel chalk line 5 1/2″ to the joint and away from it on each side of the ridge or hip. 

Begin at the chalk lines and work your way toward the joint to create a 2″ border around it. Then apply an asphalt lap cement band on both sides of the ridge or hip.

By following this process, you can easily complete rolled roofing on your pitched roof.


Rolled roofing is not a common option for your house where you live. Moreover, it is mainly used for kids’ tree houses, sheds, or barns.

It is not a long-lasting solution, so try to avoid using it on your residential building.


As a civil engineer and roofer, I love to share the experience that I have gained through the last couple of years. In the roofing industry, practical experience is a very crucial fact that can help you a lot. Hence, I want to help you with my blog.

Write A Comment